Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Tools

No Image
$197.00
- Drift and over axle set for less common thru axle hube and frame bearings - For use with 3/8" press rod - See wheelsmfg.com for full list of contents
Wheels Manufacturing Inc. Open Bore Adapters
$9.50
Wheels Manufacturing open bore adapters are used to press sealed cartridge bearings into place. The adapters are machined with one step to correspond to the bearing OD, which fits in to the center of the sealed bearing and an outside diameter to accommodate the bearing's outer diameter. Size: [Bearing inner diameter] x [Bearing outer diameter] Note: If only one dimension is given, that is the outer diameter of the adapter, with no inner diameter step
Wheels Manufacturing Inc. Over Axle Adapter
$9.50
Wheels Manufacturing Over Axle Adapters are used for pressing your most commonly used bearing sizes into place. Each represents an excellent addition to the Press-4 Bearing Press. - Adapters sold individually
Wheels Manufacturing Inc. Bearing Extractor Pusher
$13.50
Pusher for Wheels Mfg sealed bearing extractors. - For use with Wheels Mfg. 1/2-inch threaded rod press handles - Part of a system that requires additional pieces to function
Wheels Manufacturing Inc. Bottom Bracket Bearing Extractor Cup Sleeve
$22.05
Receiver cup sleeve for Wheels Mfg. sealed bearing extractors. Machined aluminum sleeve, anodized red. - 1/2-inch thru hole to fit over their 1/2-inch threaded rod press handles - Part of a system that requires additional pieces to function
Wheels Manufacturing Inc. Bottom Bracket Press Pro Install Kit
$211.00
Complete tool kit for installing wheels manufacturing bottom brackets. Kit includes our new bottom bracket socket tool for installing our BB cups, along with new sealed bearing drifts for the following ID bearings: - 22mm - 24mm - 29mm - 30mm Bottom bracket press pro install kit includes: - UNC 48mm 16-notch socket x 1 - 22x37 drift 1/2" x 1 - 6806 OB 1/2" x 2 - 24x37 OB 1/2" x2 - 1/2" frame drift x 1 1/2-13 x 9. 7" - threaded rod unc x 1 44-48. 5mm - double 16-notch 1/2" socket x 1 - threaded handle x 2
Wheels Manufacturing Inc. 2437 Open Bore Adapter For Half Inch Rod
$9.50
Our 2437 open bore adapter is used to press 24x37 sealed bearings into bottom bracket cups, and direct fit frames like trek BB90. The adapter is machined with one step at 24mm ID, which fits into the center of the sealed bearing. - Installs: 24x37 bearing - Inner step outer diameter: 23. 8mm - Outer diameter: 36. 8mm - Thru hole diameter: 0. 387" (9. 8mm) - Inner hole sized to fit 1/2" threaded rod - Compatible with BP0006, BP0007 - Machined, red anodized aluminum - Sold individually (2 drifts required for some installations)
Wheels Manufacturing Inc. Bottom Bracket Frame Drift
$18.50
Designed to press in all current wheels mfg bottom brackets! our universal bottom bracket frame drift is designed to press all current wheels mfg bottom bracket cups in to your frame. The adapter is machined with multiple steps to fit common bottom bracket shell inside diameters listed in the compatibility tab below. Each step is laser etched with the diameter size. Drift can also can be used as a frame bottom bracket shell sizing guide! - Inner hole sized to fit 1/2" threaded rod. (Not for use with our Press-1 or Press-4 ) - Compatible with any other press with a 1/2" diameter rod - Recommended for use with Wheels Mfg BP0006, BP0007 - Machined aluminum - Anodized red - Sold individually We do not recommend it for use with press with a rod diameter less than 1/2". When used with a smaller rod, it is almost impossible to prevent the cups or bearings from pressing in straight.
No Image
$204.00
- Drift and over axle set for common thru axle hube and frame bearings - For use with 3/8" press rod - See wheelsmfg.com for full list of contents
Wheels Manufacturing Inc. Bench Mount Axle/Cone Ruler
$92.40
- Anodized aluminum construction. Includes mounting hardware - Measures threads for all cones, locknuts and axles - Metric measurement on one side and Standard on the other side
Wheels Manufacturing Inc. PRESS-1 Handle & Rod Assembly
$102.50
PRESS-1 Handle & Rod Assembly Replacement Handle Assembly for our Large Sealed Bearing Press (PRESS-1). Primarily designed for pressing bearings into hubs. Note: Rod diameter is smaller than the hole size in our Universal Bottom Bracket Drift. Includes: - (1) Machined fixed end aluminum "T" Handle. - (1) Machined non-fixed end aluminum "T" Handle. - (1) 3/8" x 12" Threaded Rod - (1) M5x12 flat head screw to secure fixed-end handle to rod
Wheels Manufacturing Inc. Bearing Press Essential Kit BP0005
$75.00
- Essential bearing press for installation of bearings with a 10mm minimum ID - (1) 3/8 ACME threaded rod, (2) 30mm standoffs, (2) threaded handles
Wheels Manufacturing Inc. BB Essential Extractor Kit EX0003
$170.00
- Essential bottom bracket bearing extractor set - (1) 6806 extractor, (1) 24x37 extractor, (1) 29 DUB extractor, (1) 22mm GXP extractor
Wheels Manufacturing Inc. Shimano Preload Tool
$29.95
Precision-machined anodized aluminum tool designed to allow for easy installation, removal, or adjustments of the Shimano Hollowtech II Crankset compression bolt.
Wheels Manufacturing Inc. Economy Bearing Press
$57.50
An indispensable tool for the serious amateur bike mechanic or smaller bike shop, the Wheels Manufacturing Bearing Press is designed for installation of bottom brackets or sealed bearings with a minimum I.D. of 10mm. - Package includes 2 handles and a 3/8"-12 threaded rod - Economy Bearing Press, used with separately-purchased bearing adaptors
Wheels Manufacturing Inc. Bearing Extractor Set
$35.00
- Sealed bearing extractor with 1/2-inch thru hole for use with Wheels Mfg. 1/2-inch threaded rod press handles - Part of a system that requires additional pieces to function
Wheels Manufacturing Inc. Sealed Bearing Extractor 9mm
$39.95
Wheels Manufacturing Sealed Bearing Extractor - 9mm Fits: - 609 - 9227 - Other bearings with an inside diameter of 9mm
Wheels Manufacturing Inc. Shock Bushing Press Kit
$115.00
Shock Bushing Press Kit An evolution of our original bushing toolset which required the use of a hammer to pound out shock bushings. The new design uses our threaded handle press system to easily and efficiently remove shock bushing in 12mm and 1/2 inch sizes. - Fits 12mm and 1/2" bushings. - Machined aluminum - Anodized Red
Wheels Manufacturing Inc. Thin Flange Bottom Bracket Socket
$45.00
Thin flange bottom bracket socket designed to create a tight grip on thin flange bottom bracket to avoid slipping while torquing cups into bike frames. This single-sided socket is used for installing and removing 48.5mm, 16-notch bottom bracket cups. The socket has a machined 3/8" drive, which can be used to allow 3/8" drive torque wrenches to be attached and locks onto 1/2 inch unc press rod for secure and easy installation of thin flanged bottom brackets. Machined 6061 aluminum anodized red
Wheels Manufacturing Inc. Bottom Bracket Gauge
$26.25
The Bottom Bracket Gauge Tool was designed to provide all the necessary measurements to identify the proper bottom bracket for a specific bike configuration. A metric scale runs along the long edges for measuring bottom bracket shell width and crank spindle lengths. Durable red anodized aluminum with laser etching. Overall size is 7" x 3" x 0.125". The gauge can measure: - bottom bracket width - bottom bracket shell inner diameter - crank spindle length - crank spindle diameter - bearing inner diameter Specifications: Measures crank spindle diameters: 22mm, 24mm, 29mm, 30mm Measures bearing inner diameters: 22mm, 24mm, 29mm, 30mm Measures bottom bracket shell inner diameters: 37mm, 41mm, 42mm, 46mm Measures bottom bracket shell widths: 61mm, 68mm, 73mm, 79mm, 86.5mm, 90mm, 92mm, 95mm, 100mm, 120mm, and 132mm Measures crank spindle lengths up to 180mm
Wheels Manufacturing Inc. BB Pro Extractor Kit EX0004
$185.00
- Advance bottom bracket bearing extractor set - (1) BE-22mm, (1) BE-24mm, (1) BE-29mm, (1) BE-30mm, (1) Bearing Pusher, (1) 39mm sleeve, (1) 42mm sleeve, (1) 44mm sleeve, (1) receiver cup
No Image
$275.00
- Press set for common frame and through axle hub bearing sizes - See wheelsmfg.com for full list of contents
Wheels Manufacturing Inc. Professional Bottom Bracket Tool Kit
$290.00
This is Wheels Manufacturing's new toolkit for installing, removing, and servicing Wheels Manufacturing bottom brackets. The kit includes their new bottom bracket socket tools for installing and removing Wheels Mfg. BB cups with the following spline patterns: 48.5mm 16-notch, 44mm 16-notch (may be compatible with FSA MegaEVO BB cups, Shimano, SRAM/Truvativ and FSA). It also includes sealed bearing extractors for 22mm, 24mm, and 30mm ID bearings. Includes - T-Handles with 1/2" threaded rod - (2) Universal bottom bracket drift (BB-OB) - (1) 48.5mm/44mm, 16-notch Bottom Bracket Socket - (1) 48.5mm, 16-notch Single Sided BB Socket - (1) 30mm ID sealed bearing extractor - (1) 24mm ID sealed bearing extractor - (1) 22mm ID sealed bearing extractor - (1) receiver cup - (1) 44mm receiver cup sleeve - (1) 42mm receiver cup sleeve - (1) 39mm receiver cup sleeve - (1) bearing pusher shaft - (1) 3/8" to 1/2" square drive adapter - Wood base
Wheels Manufacturing Inc. Sealed Bearing Extractor 17mm
$39.95
Wheels Manufacturing Sealed Bearing Extractor - 17mm Fits the following bearings: - 6003 - 6803 - 6903 - 17287
Wheels Manufacturing Inc. Sealed Bearing Extractor 9.5mm
$41.95
Wheels Manufacturing Sealed Bearing Extractor - 9.5mm Fits: - R6 (3/8-inch) bearings - Other bearings with an inside diameter of 9.5mm
Wheels Manufacturing Inc. Sealed Bearing Extractor 15mm
$39.95
Wheels Manufacturing Sealed Bearing Extractor - 15mm Fits the following bearings: - 6002 - 6702 - 6802 - 6902 - 15267 - 15268
No Image
$125.00
- Bottom bracket and bearing installation kit - (1) 1/2" rod, (2) threaded handles - (1) 2237 OPEN BORE, (2) 2437 OPEN BORE, (2) 29mm OPEN BORE, (2) 6806 OPEN BORE, (1) FRAME DRIFT
Wheels Manufacturing Inc. Headset Press Pro Install Kit
$187.00
The Headset Press Pro Install Kit is a robust, and easy to use tool. The kit includes a machined aluminum handle, 1/2" threaded rod, two machined aluminum drifts and the adjustable press stop allowing for easy drift placement. One drift is machined with multiple steps to fit common head tube inner diameters listed in the compatibility tab below. The other drift has two sizes to press in cups with either 1-1/8" or 1-1/2" bearings. - machined aluminum handle and drifts - red anodized drifts and handles - zinc-plated 1/2" diameter threaded rod - long threaded rod works with long head tubes up to 250mm includes - 1 head tube drift includes - 1 headset cup drift - 1 adjustable press stop - 1 threaded handle includes on 1/2"-13x17" unc threaded rod
Wheels Manufacturing Inc. Hub Bearing Extractor Kit EX0001
$160.00
- Bearing extractor set for small bearings - (1) 608, (1) 609, (1) 6000, (1) 6001
Wheels Manufacturing Inc. 29mm SRAM DUB Open Bore Adapter
$9.50
This 29mm open bore adapter is used to press 29mm x 42mm (DUB) sealed bearings. The adapter is machined with one step at 29mm OD, which fits into the center of the sealed bearing. For use with Wheels Mfg. bottom bracket press (PRESS-7 , PRESS-7-PRO or PRESS-9-PRO). - Inner step outer diameter: 28.9mm - Outer diameter: 41.8mm - Thru hole diameter: 12.8mm (1/2-inch) - Thickness: 7mm - Machined, red anodized aluminum - Sold individually
Page 1 of 2 Next page